Transfer case and vehicle shafts Nissan X-Trail 2 (T31)
Transfer Case Oil (TY30A)
Examination Oil leak Check for oil leaks from and around the transfer case (oil seal, crankcase drain plug, etc.) Oil level 1. Unscrew the plug (1) from the filler hole...
Examination Oil leak Check for oil leaks from and around the transfer case (oil seal, crankcase drain plug, etc.) Oil level 1. Unscrew the plug (1) from the filler hole...
On-Vehicle Service — 4WD Control Unit (TY30A)
Removal and installation Removal 1. Remove the glove box cover assembly. Refer to Chapter " Interior and exterior body equipment ". 2. Disconnect the connector from the...
Removal and installation Removal 1. Remove the glove box cover assembly. Refer to Chapter " Interior and exterior body equipment ". 2. Disconnect the connector from the...
Transfer case assembly — engines MR20DE (manual transmission), QR25DE (manual transmission)
Removal and installation Removal 1. Remove the following components: front exhaust pipe. See chapter " Accelerator. Fuel and exhaust systems "; intake manifold, see...
Removal and installation Removal 1. Remove the following components: front exhaust pipe. See chapter " Accelerator. Fuel and exhaust systems "; intake manifold, see...
Transfer case assembly — engines MR20DE (CVT), QR25DE (CVT)
Removal and installation Removal 1. Remove the following components: front exhaust pipe, see chapter " Accelerator, fuel system and exhaust system "; intake manifold,...
Removal and installation Removal 1. Remove the following components: front exhaust pipe, see chapter " Accelerator, fuel system and exhaust system "; intake manifold,...
Rear Propeller Shaft — On-Vehicle Service (3FSPL18-DOJ75)
Checking the appearance and knocking Check the driveshaft tube for nicks or cracks. Replace the driveshaft assembly if necessary. If the center bearing makes unusual...
Checking the appearance and knocking Check the driveshaft tube for nicks or cracks. Replace the driveshaft assembly if necessary. If the center bearing makes unusual...
Vehicle repair (3FSPL18-DOJ75)
1. Cardan shaft assembly; 2. Center bearing mounting bracket (upper); 3. Clamp; 4. Center bearing mounting bracket (lower) Removal and installation Removal 1. Shift the...
1. Cardan shaft assembly; 2. Center bearing mounting bracket (upper); 3. Clamp; 4. Center bearing mounting bracket (lower) Removal and installation Removal 1. Shift the...
Rear final drive — sectional view (R145)
Sectional view 1. Connecting flange; 2. Electronically controlled clutch; 3. 4WD solenoid; 4. Central seal; 5. Front pinion bearing; 6. Split spacer; 7. Rear bearing of...
Sectional view 1. Connecting flange; 2. Electronically controlled clutch; 3. 4WD solenoid; 4. Central seal; 5. Front pinion bearing; 6. Split spacer; 7. Rear bearing of...
Transmission oil for rear differential (R145)
Examination Oil leak Check for oil leakage from and around the final drive assembly. Oil level Remove the plug (1) from the filler hole and check the oil level through...
Examination Oil leak Check for oil leakage from and around the final drive assembly. Oil level Remove the plug (1) from the filler hole and check the oil level through...
Car repair — front oil seal (R145)
Engines MR20DE (MCL, CVT) and QR25DE (manual gearbox). 1. Main gear assembly; 2. Front oil seal; 3. Connecting flange; 4. Locknut of connecting flange; A. Oil seal lip....
Engines MR20DE (MCL, CVT) and QR25DE (manual gearbox). 1. Main gear assembly; 2. Front oil seal; 3. Connecting flange; 4. Locknut of connecting flange; A. Oil seal lip....
Car repair — axle shaft seal (R145)
Axle shaft seal. 1. Main gear assembly; 2. Axle shaft seal; A. Seal lip Removal and installation Removal 1. Remove the rear drive shafts. See chapter " Rear axle and...
Axle shaft seal. 1. Main gear assembly; 2. Axle shaft seal; A. Seal lip Removal and installation Removal 1. Remove the rear drive shafts. See chapter " Rear axle and...
Car Repair — Electronically Controlled Clutch (R145)
Engines MR20DE (manual gearbox, CVT) and OR25DE (manual gearbox) 1. Main gear assembly; 2. Central seal; 3. Solenoid wiring; 4. Clutch with electronic control; 5....
Engines MR20DE (manual gearbox, CVT) and OR25DE (manual gearbox) 1. Main gear assembly; 2. Central seal; 3. Solenoid wiring; 4. Clutch with electronic control; 5....
Removal and installation — rear final drive assembly (R145)
1. Rear final drive mounting bracket. 2. Washer. 3. Main gear assembly. Removal 1. Remove the rear propeller shaft. See above 2. Remove the rear drive shafts. See...
1. Rear final drive mounting bracket. 2. Washer. 3. Main gear assembly. Removal 1. Remove the rear propeller shaft. See above 2. Remove the rear drive shafts. See...
Technical data and specifications
Model TY30A General information Applied to the model 4WD MR20DE, QR25DE MKP CVT Transfer case model TY30A Oil filling capacity (approx.) l. 0,38 0,36 Gear ratio 0,656...
Model TY30A General information Applied to the model 4WD MR20DE, QR25DE MKP CVT Transfer case model TY30A Oil filling capacity (approx.) l. 0,38 0,36 Gear ratio 0,656...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar information for other Nissan models
➜ Transmission: Transfer case Nissan Murano 1 (2002-2007, petrol)
➜ Transmission: Transfer case Nissan Serena 2 (1999-2005)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- Control devices
- Operating instructions
- Maintenance
- Powertrain MR20DE
- Engine repair
- Lubrication system
- Cooling system
- Control system
- Fuel and exhaust system
- Powertrain QR25DE
- Engine repair
- Lubrication system
- Cooling system
- Control system
- Transmission
- Clutch
- Mechanical gearbox
- Variator (CVT)
- Transfer case
- Chassis
- Front suspension
- Rear suspension
- Brake system
- Steering
- Body
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Lighting system
- Windshield wipers and washers
- Engine electrical equipment
Cookies are used to improve the site's performance. 💻 Continue by agreeing to the terms.