Vehicle Fuel Injection Units Nissan Sunny 7 (B13)
Fuel distributor and injectors — removal and installation
Removal 1. Disconnect the battery from ground and remove the air filter. 2. Disconnect the vacuum tube from the pressure regulator. 3. Decompress the fuel system and...
Removal 1. Disconnect the battery from ground and remove the air filter. 2. Disconnect the vacuum tube from the pressure regulator. 3. Decompress the fuel system and...
Pressure regulator — removal and installation
Removal 1. Disconnect the battery from ground. 2. Disconnect the vacuum tube (arrow) from the pressure regulator. 3. Decompress the fuel system and disconnect the fuel...
Removal 1. Disconnect the battery from ground. 2. Disconnect the vacuum tube (arrow) from the pressure regulator. 3. Decompress the fuel system and disconnect the fuel...
Throttle Position Sensor — Removal and Installation
Sensor location Angle sensor (variable resistance) mounted on the right side of the damper body. Removal and installation 1. Disconnect the battery from ground. 2....
Sensor location Angle sensor (variable resistance) mounted on the right side of the damper body. Removal and installation 1. Disconnect the battery from ground. 2....
Air bypass valve — removal and installation
The valve is mounted in the front part of the damper body. Removal 1. Disconnect the battery from ground. 2. Disconnect the connector from the valve (1 – connector, 2 –...
The valve is mounted in the front part of the damper body. Removal 1. Disconnect the battery from ground. 2. Disconnect the connector from the valve (1 – connector, 2 –...
Flow Meter — Removal and Installation
The meter is mounted on the right side of the valve body. Removal 1. Disconnect the battery from ground. 2. Disconnect the connector. 3. Unscrew the screws (indicated by...
The meter is mounted on the right side of the valve body. Removal 1. Disconnect the battery from ground. 2. Disconnect the connector. 3. Unscrew the screws (indicated by...
Idle speed correction valve for engine load changes
Valve location The correction valve is screwed into the damper body. Removal 1. Disconnect the battery from ground and remove the air filter. 2. Disconnect the...
Valve location The correction valve is screwed into the damper body. Removal 1. Disconnect the battery from ground and remove the air filter. 2. Disconnect the...
High idle speed thermostat
The thermostat is mounted on the left side of the damper body. Removal 1. Disconnect the battery from ground. 2. Remove the air filter. 3. Remove the nut and remove the...
The thermostat is mounted on the left side of the damper body. Removal 1. Disconnect the battery from ground. 2. Remove the air filter. 3. Remove the nut and remove the...
Crankshaft angle sensor and transistor module
The crankshaft angle sensor and transistor module are built into the ignition distributor, which is only replaced as an assembly.
The crankshaft angle sensor and transistor module are built into the ignition distributor, which is only replaced as an assembly.
Processor unit — removal and installation
The unit is mounted under the central section of the front panel, on the transmission tunnel casing. Removal 1. Disconnect the battery from ground. 2. Remove the screws,...
The unit is mounted under the central section of the front panel, on the transmission tunnel casing. Removal 1. Disconnect the battery from ground. 2. Remove the screws,...
Idle speed correction switch when operating the power steering
The switch is screwed into the power steering circuit on the right rear of the engine compartment. Removal 1. Place the wheels in a straight-ahead position and...
The switch is screwed into the power steering circuit on the right rear of the engine compartment. Removal 1. Place the wheels in a straight-ahead position and...
Idle speed correction switch when the air conditioner is running
The switch is screwed into the air conditioning circuit in the left front part of the engine compartment. It can only be changed by a car service, as it is necessary to...
The switch is screwed into the air conditioning circuit in the left front part of the engine compartment. It can only be changed by a car service, as it is necessary to...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Faults en route
- Maintenance
- Power unit
- Petrol engines (1.4 and 1.6)
- Engine overhaul (1.4 and 1.6)
- Petrol engines (2.0)
- Engine overhaul (2.0)
- Diesel engine
- Cooling system
- Heating and ventilation
- Power system (carburetor)
- Power system (injector)
- Fuel injection system
- Single point injection
- Multi-point injection
- Decreased toxicity
- Engine electrical equipment
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis
- Brake system
- Car suspension
- Steering
- Body
- Body repair
- Body elements
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits
Cookies are used to improve the site's performance. 💻 Continue by agreeing to the terms.