Car clutch and drive shafts Nissan Primera 1 (P10)
On the models in question, a single-disk dry clutch with a diaphragm spring is installed. The clutch is driven by a cable.
Clutch and Drive Shaft Specifications
Note: Individual characteristics are also given in the text of the Chapter and, if mandatory and fulfilled, are highlighted in bold Clutch Design Single-plate dry clutch...
Note: Individual characteristics are also given in the text of the Chapter and, if mandatory and fulfilled, are highlighted in bold Clutch Design Single-plate dry clutch...
Checking the clutch in the installed state
Before removing the clutch for replacement, you can perform the following work to check where the fault may be located. 1. Start the engine and let it idle. 2. Depress...
Before removing the clutch for replacement, you can perform the following work to check where the fault may be located. 1. Start the engine and let it idle. 2. Depress...
Removal the clutch
The clutch can only be removed after removing the entire unit and then disconnecting the engine or after separately removing the gearbox. 1. Remove the engine or gearbox...
The clutch can only be removed after removing the entire unit and then disconnecting the engine or after separately removing the gearbox. 1. Remove the engine or gearbox...
Clutch repair
1. Check the pressure plate and cover for damage or bending. If damaged, replace both parts as a set. Check the condition of the driven disk springs and spline...
1. Check the pressure plate and cover for damage or bending. If damaged, replace both parts as a set. Check the condition of the driven disk springs and spline...
Clutch installation
The clutch is installed in the reverse order. The following points should be taken into account: 1. A centering rod is usually required to center the driven disk...
The clutch is installed in the reverse order. The following points should be taken into account: 1. A centering rod is usually required to center the driven disk...
Clutch adjustment
Clutch parts 1 - flywheel; 2 - slave disk; 3 - bolts, 22-29 Nm; 4 - clutch basket; 5 - primary shaft of the gearbox Two adjustments may be required - clutch pedal height...
Clutch parts 1 - flywheel; 2 - slave disk; 3 - bolts, 22-29 Nm; 4 - clutch basket; 5 - primary shaft of the gearbox Two adjustments may be required - clutch pedal height...
Clutch release mechanism
1. Remove the power unit and disconnect the gearbox from the engine (Chapter Engine ) or remove the gearbox (Chapter Manual transmission, differential and final drive )....
1. Remove the power unit and disconnect the gearbox from the engine (Chapter Engine ) or remove the gearbox (Chapter Manual transmission, differential and final drive )....
Clutch faults
As already mentioned, the clutch can slip. The clutch can also jerk. When the clutch jerks, the car moves jerkily, i.e. the transmission of engine speed to the drive...
As already mentioned, the clutch can slip. The clutch can also jerk. When the clutch jerks, the car moves jerkily, i.e. the transmission of engine speed to the drive...
Clutch shaft guide bearing
The pilot bearing on the inside of the flywheel can be checked in the installed condition by inserting your index finger into the bearing and rotating it from side to...
The pilot bearing on the inside of the flywheel can be checked in the installed condition by inserting your index finger into the bearing and rotating it from side to...
Clutch flywheel — check
If the clutch is removed, the flywheel and its ring gear teeth should be checked. Since the ring gear is not replaced separately, the entire flywheel should be replaced....
If the clutch is removed, the flywheel and its ring gear teeth should be checked. Since the ring gear is not replaced separately, the entire flywheel should be replaced....
Drive shafts — general information
Each end of the drive shaft is fitted with a constant velocity joint. All vehicles have a closed joint at the outer end of the shaft that can be replaced but not...
Each end of the drive shaft is fitted with a constant velocity joint. All vehicles have a closed joint at the outer end of the shaft that can be replaced but not...
Removal and installation drive shafts
Removal and installation of drive shafts should be carried out together with the hub and steering knuckle, these works are described in Chapter Suspension and steering ....
Removal and installation of drive shafts should be carried out together with the hub and steering knuckle, these works are described in Chapter Suspension and steering ....
Drive shaft repair
Details of a disassembled drive shaft with a sprocket joint inside 1 - retaining ring; 2 - internal constant velocity joint; 3 - retaining ring; 4 - joint star; 5 -...
Details of a disassembled drive shaft with a sprocket joint inside 1 - retaining ring; 2 - internal constant velocity joint; 3 - retaining ring; 4 - joint star; 5 -...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar information for other Nissan models
➜ Transmission: Clutch Nissan X-Trail 2 (2007-2013, petrol)
➜ Transmission: Clutch and drive shafts Nissan Maxima 4 (1994-1999)
➜ Transmission: Clutch Nissan Micra 3 (2002-2010, petrol)
➜ Transmission: Clutch and drive shafts Nissan Terrano 1 (1986-1995, petrol)
➜ Transmission: Clutch Nissan Bluebird T12 (1986-1991)
➜ Transmission: Clutch Nissan Patrol 4 (1987-1997, petrol)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- Introduction to the guide
- Maintenance
- Power unit
- Engine repair
- Cooling and heating
- Power and exhaust system
- Engine electrical equipment
- Transmission
- Mechanical gearbox
- Automatic gearbox
- Clutch and drive shafts
- Chassis
- Brake system
- Front suspension
- Rear suspension
- Steering
- Body and electrical equipment
- Body repair
- Equipment and devices
Cookies are used to improve the site's performance. 💻 Continue by agreeing to the terms.