Vehicle intake and exhaust system Nissan Qashqai 1 (J10)
Precautionary measures
Attention. Use only original or equivalent spare parts, as they are able to withstand high temperatures, have high corrosion resistance and have the correct geometry....
Attention. Use only original or equivalent spare parts, as they are able to withstand high temperatures, have high corrosion resistance and have the correct geometry....
Replacing the air filter of the intake system (petrol engines (HR16DEU, MR20DE) and diesel M9R)
Removal and installation 1. Unclip the clamps (A) and remove the holder (2) from the air filter housing (1). 2. Remove the air filter (1) from the housing (2). 3....
Removal and installation 1. Unclip the clamps (A) and remove the holder (2) from the air filter housing (1). 2. Remove the air filter (1) from the housing (2). 3....
Replacing the air filter of the intake system (diesel engine K9K)
Removal and installation 1. Open the air filter housing. 2. Remove the air filter (1). 3. Installation is carried out in the reverse order of removal.
Removal and installation 1. Open the air filter housing. 2. Remove the air filter (1). 3. Installation is carried out in the reverse order of removal.
Exhaust system
Check the exhaust pipes, mufflers and brackets, paying attention to improper fastening, leaks, cracks, damage and wear. If a fault is found, it should be repaired or the...
Check the exhaust pipes, mufflers and brackets, paying attention to improper fastening, leaks, cracks, damage and wear. If a fault is found, it should be repaired or the...
Air intake tract with air filter — device
Engine HR16DE: 1. Air filter. 2. Holder. 3. Compaction. 4. Air filter housing. 5. Sealing ring. 6. Mass air flow sensor. 7. Clamp. 8. Air duct with resonator assembly....
Engine HR16DE: 1. Air filter. 2. Holder. 3. Compaction. 4. Air filter housing. 5. Sealing ring. 6. Mass air flow sensor. 7. Clamp. 8. Air duct with resonator assembly....
Air intake tract with air filter — removal and installation
Note: The procedures below are described using petrol engine versions as an example. The operations for diesel versions are similar, taking into account the design...
Note: The procedures below are described using petrol engine versions as an example. The operations for diesel versions are similar, taking into account the design...
Intake manifold of the HR16DE engine — device
1. Fuel vapor recovery system hose. 2. Vacuum receiver. 3. Fuel vapor recovery system hose 4. O-ring round section. 5. Electromagnetic valve for controlling the purge...
1. Fuel vapor recovery system hose. 2. Vacuum receiver. 3. Fuel vapor recovery system hose 4. O-ring round section. 5. Electromagnetic valve for controlling the purge...
HR16DE Engine Intake Manifold — Removal and Installation
1. Remove the intake air duct with the resonator assembly (see the relevant section above). 2. Disconnect the water hoses from the electronic throttle actuator, plug the...
1. Remove the intake air duct with the resonator assembly (see the relevant section above). 2. Disconnect the water hoses from the electronic throttle actuator, plug the...
Intake manifold of the MR20DE engine — device
1. Clamp. 2. Wiring harness bracket. 3. Hose of the forced crankcase ventilation system. 4. Gasket. 5. Vacuum hose. 6. Intake manifold. 7. Bracket. 8. Engine cover. 9....
1. Clamp. 2. Wiring harness bracket. 3. Hose of the forced crankcase ventilation system. 4. Gasket. 5. Vacuum hose. 6. Intake manifold. 7. Bracket. 8. Engine cover. 9....
MR20DE Engine Intake Manifold — Removal and Installation
1. Remove the engine cover. 2. Remove the oil dipstick. Caution: Cover the dipstick guide hole to prevent foreign material from entering. 3. Disconnect the forced...
1. Remove the engine cover. 2. Remove the oil dipstick. Caution: Cover the dipstick guide hole to prevent foreign material from entering. 3. Disconnect the forced...
Intake manifold of the M9R engine — device
1. Gasket. 2. Intake manifold. 3. Electronic throttle control drive stand. 4. Electronic throttle control drive. 5. Gasket. 6. Boost pressure sensor. 7. Boost pressure...
1. Gasket. 2. Intake manifold. 3. Electronic throttle control drive stand. 4. Electronic throttle control drive. 5. Gasket. 6. Boost pressure sensor. 7. Boost pressure...
M9R Engine Intake Manifold — Removal and Installation
1. Remove the engine cover. 2. Remove the air intake duct. 3. Remove the air intake hose and air intake duct. 4. Remove the oil dipstick from the guide. 5. Remove the...
1. Remove the engine cover. 2. Remove the air intake duct. 3. Remove the air intake hose and air intake duct. 4. Remove the oil dipstick from the guide. 5. Remove the...
Exhaust manifold (petrol engines) — device
Engine HR16DE: 1. Exhaust manifold cover. 2. Exhaust manifold cover. 3. Wiring harness bracket. 4. Heated oxygen sensor 1. 5. Exhaust manifold stand. 6. Exhaust...
Engine HR16DE: 1. Exhaust manifold cover. 2. Exhaust manifold cover. 3. Wiring harness bracket. 4. Heated oxygen sensor 1. 5. Exhaust manifold stand. 6. Exhaust...
Exhaust manifold (petrol engines) — removal and installation
1. Remove the front exhaust pipe. 2. Remove the heated oxygen sensor 1 wiring harness bracket from the cylinder head. 3. Remove the exhaust manifold cover. 4. Using a...
1. Remove the front exhaust pipe. 2. Remove the heated oxygen sensor 1 wiring harness bracket from the cylinder head. 3. Remove the exhaust manifold cover. 4. Using a...
Diesel engine K9K — device
1. Gasket. 2. Exhaust manifold. A. To the cylinder head. Note. : replace the part with a new one after each removal.
1. Gasket. 2. Exhaust manifold. A. To the cylinder head. Note. : replace the part with a new one after each removal.
Diesel engine K9K — removal and installation
1. Disconnect the negative battery terminal. 2. Remove the engine protective pan. 3. Remove the air filter housing with the air intake duct. 4. Remove the windshield...
1. Disconnect the negative battery terminal. 2. Remove the engine protective pan. 3. Remove the air filter housing with the air intake duct. 4. Remove the windshield...
Diesel engine M9R — device
MR20DE Engine: 1. Gasket. 2. Spacer. 3. Exhaust manifold. 4. Putting on. A. To the turbocharger. B. To the rear exhaust gas recirculation pipe. Note. : replace the part...
MR20DE Engine: 1. Gasket. 2. Spacer. 3. Exhaust manifold. 4. Putting on. A. To the turbocharger. B. To the rear exhaust gas recirculation pipe. Note. : replace the part...
Diesel Engine M9R — Removal and Installation
1. Drain the coolant from the engine. Caution: Perform this step only on a cold engine. 2. Remove the catalytic converter. 3. Remove the turbocharger. 4. Remove the air...
1. Drain the coolant from the engine. Caution: Perform this step only on a cold engine. 2. Remove the catalytic converter. 3. Remove the turbocharger. 4. Remove the air...
Exhaust pipe and mufflers
Note. When removing and installing exhaust system components, it is recommended to refer to the general appearance drawings below. To remove the heated oxygen sensor 2,...
Note. When removing and installing exhaust system components, it is recommended to refer to the general appearance drawings below. To remove the heated oxygen sensor 2,...
Intercooler for charge air of diesel engines (intercooler)
Versions with K9K engine: 1. Air inlet hose. 2. Clamp. 3. Air intake duct. 4. Air inlet hose. 5. Air intake duct. 6. Gasket. 7. Intercooler of charge air. 8. Gasket. 9....
Versions with K9K engine: 1. Air inlet hose. 2. Clamp. 3. Air intake duct. 4. Air inlet hose. 5. Air intake duct. 6. Gasket. 7. Intercooler of charge air. 8. Gasket. 9....
Intercooler — Removal and Installation
Note: The procedures below are described using the K9K engine version as an example. The operations for M9R engine versions are similar, taking into account the design...
Note: The procedures below are described using the K9K engine version as an example. The operations for M9R engine versions are similar, taking into account the design...
Diesel Engine Intercooler — Checking After Removal
1. Check for oil on the intercooler. If oil is found, remove it with a cleaning agent and dry it. 2. Check the air channels and fins of the charge air intercooler core...
1. Check for oil on the intercooler. If oil is found, remove it with a cleaning agent and dry it. 2. Check the air channels and fins of the charge air intercooler core...
Turbocharger — device
Versions with K9K engine: 1. Washer. 2. Turbocharger pressure oil line. 3. O-ring round section. 4. Turbocharger. 5. Exhaust manifold. 6. Turbocharger oil outlet line....
Versions with K9K engine: 1. Washer. 2. Turbocharger pressure oil line. 3. O-ring round section. 4. Turbocharger. 5. Exhaust manifold. 6. Turbocharger oil outlet line....
Turbocharger — removal and installation
Note: The procedures below are described using the K9K engine version as an example. The operations for M9R engine versions are similar, taking into account the design...
Note: The procedures below are described using the K9K engine version as an example. The operations for M9R engine versions are similar, taking into account the design...
Turbocharger — Checking after removal
Attention. If the turbine wheel or rotor shaft has been damaged, remove all debris and foreign particles from the following passages to prevent secondary engine damage:...
Attention. If the turbine wheel or rotor shaft has been damaged, remove all debris and foreign particles from the following passages to prevent secondary engine damage:...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar information for other Nissan models
➜ Power unit: Exhaust system Nissan Murano 1 (2002-2007, petrol)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- Faults en route
- Daily checks
- User manual
- Maintenance
- Power unit
- Petrol engines 1.6L (HR16)
- Petrol engines 2.0L (MR20)
- Diesel engines 1.5L (K9K)
- Diesel engines 2.0L (M9R)
- Cooling system
- Engine lubrication system
- Engine power system
- Engine management system
- Intake and exhaust system
- Engine electrical equipment
- Transmission
- Clutch
- Car gearbox
- Transfer case and shafts
- Chassis
- Car suspension
- Brake system
- Steering
- Body
- Exterior (external elements)
- Interior (internal elements)
- Safety system
- Heating and air conditioning
- Electrical equipment
- Wiring harnesses
Cookies are used to improve the site's performance. 💻 Continue by agreeing to the terms.