Car engine cooling system Nissan Qashqai 1 (J10)
Checking the coolant level
1. Check that the coolant level in the expansion tank is between the "MIN" and "MAX" marks on a cold engine. 2. If necessary, adjust the coolant level. 3. Make sure the...
1. Check that the coolant level in the expansion tank is between the "MIN" and "MAX" marks on a cold engine. 2. If necessary, adjust the coolant level. 3. Make sure the...
Checking the tightness of the cooling system
To check for leaks, install an adapter on the expansion tank and connect a cooling system tester to it (M.S.554-07) (A) as shown in the figure. Attention. Do not remove...
To check for leaks, install an adapter on the expansion tank and connect a cooling system tester to it (M.S.554-07) (A) as shown in the figure. Attention. Do not remove...
Replacing the coolant
Draining the coolant Attention. To avoid burns, do not change the fluid on a hot engine. Wrap the radiator cap with a thick layer of rag and unscrew the cap. First, turn...
Draining the coolant Attention. To avoid burns, do not change the fluid on a hot engine. Wrap the radiator cap with a thick layer of rag and unscrew the cap. First, turn...
Checking the radiator cap
1. Check the condition of the steam valve gasket. Looking at the plug from above, check whether the gasket has swollen so much that it obscures the metal plunger from...
1. Check the condition of the steam valve gasket. Looking at the plug from above, check whether the gasket has swollen so much that it obscures the metal plunger from...
Radiator check
Check the radiator for dirt or deposits. If necessary, clean the radiator as described below. Be careful not to bend or damage the radiator tubes. When cleaning the...
Check the radiator for dirt or deposits. If necessary, clean the radiator as described below. Be careful not to bend or damage the radiator tubes. When cleaning the...
Radiator and cooling system fan — device
Versions with petrol engines 1. Expansion tank cap. 2. Expansion tank. 3. Clamp 4. Expansion tank hose. 5. Expansion tank hose. 6. Clamp. 7. Bracket. 8. Upper elastic...
Versions with petrol engines 1. Expansion tank cap. 2. Expansion tank. 3. Clamp 4. Expansion tank hose. 5. Expansion tank hose. 6. Clamp. 7. Bracket. 8. Upper elastic...
Removal the radiator
Attention. Do not remove the radiator cap when the engine is hot. Hot coolant escaping from the radiator under high pressure can cause serious burns. Wrap the cap with a...
Attention. Do not remove the radiator cap when the engine is hot. Hot coolant escaping from the radiator under high pressure can cause serious burns. Wrap the cap with a...
Installing a radiator
Installation is carried out in the reverse order of removal. Post-installation check 1. Make sure the expansion tank cap is tightened. 2. Check the tightness of the...
Installation is carried out in the reverse order of removal. Post-installation check 1. Make sure the expansion tank cap is tightened. 2. Check the tightness of the...
Water pump — device
Petrol engine HR16DE 1. Gasket. 2. Water pump. 3. Water pump pulley. Petrol engine MR20DE 1. Gasket. 2. Water pump. Diesel engine K9K: 1. Water pump. 2. Water pump...
Petrol engine HR16DE 1. Gasket. 2. Water pump. 3. Water pump pulley. Petrol engine MR20DE 1. Gasket. 2. Water pump. Diesel engine K9K: 1. Water pump. 2. Water pump...
Removal the water pump
1. Drain the coolant from the radiator. Attention. Drain the coolant only after the engine has cooled down. Prevent coolant from coming into contact with drive belts. 2....
1. Drain the coolant from the radiator. Attention. Drain the coolant only after the engine has cooled down. Prevent coolant from coming into contact with drive belts. 2....
Installing a water pump
Installation is carried out in the reverse order of removal. Caution: Do not install the water pump pulley mounting bolts (A) into the oblong holes (B).
Installation is carried out in the reverse order of removal. Caution: Do not install the water pump pulley mounting bolts (A) into the oblong holes (B).
Water pump checks
Check after removal 1. Visually check the water pump body for dirt or rust. 2. Make sure there is no play in the blade shaft. Check whether it rotates freely with manual...
Check after removal 1. Visually check the water pump body for dirt or rust. 2. Make sure there is no play in the blade shaft. Check whether it rotates freely with manual...
Thermostat and cooling system outlet (petrol engines) — device
Engine thermostat HR16DE: 1. Upper radiator hose. 2. Inlet pipe of the cooling system. 3. Rubber ring. 4. Thermostat. A. To the radiator. Output of the HR16DE engine...
Engine thermostat HR16DE: 1. Upper radiator hose. 2. Inlet pipe of the cooling system. 3. Rubber ring. 4. Thermostat. A. To the radiator. Output of the HR16DE engine...
Removal the thermostat (petrol engines)
1. Drain the coolant from the radiator. Attention. This step is performed on a cold engine. Do not allow coolant to come into contact with the accessory drive belt. 2....
1. Drain the coolant from the radiator. Attention. This step is performed on a cold engine. Do not allow coolant to come into contact with the accessory drive belt. 2....
Installing a thermostat (petrol engines)
Installation is carried out in the reverse order of removal. Note: The thermostat must be installed so that the float valve is on top and the rubber ring (1) is evenly...
Installation is carried out in the reverse order of removal. Note: The thermostat must be installed so that the float valve is on top and the rubber ring (1) is evenly...
Removal and installation the cooling system outlet (petrol engines)
Removal 1. Drain the coolant from the radiator. Attention. This step is performed on a cold engine. Do not allow coolant to come into contact with the accessory drive...
Removal 1. Drain the coolant from the radiator. Attention. This step is performed on a cold engine. Do not allow coolant to come into contact with the accessory drive...
Thermostat and cooling system outlet (diesel engines) — device
Engine K9K: 1. O-ring round section. 2. EGR cooler cover. 3. Clamp. 4. Water pipe. 5. Heater hose. 6. Clamp. 7. Coolant temperature sensor. 8. O-ring round section. 9....
Engine K9K: 1. O-ring round section. 2. EGR cooler cover. 3. Clamp. 4. Water pipe. 5. Heater hose. 6. Clamp. 7. Coolant temperature sensor. 8. O-ring round section. 9....
Removal and installation the thermostat (diesel engines)
Removal 1. Remove the engine cover. 2. Remove the air filter housing and air intake duct. 3. Remove the rear engine lifting eye. 4. Remove the vacuum hose. 5. Remove the...
Removal 1. Remove the engine cover. 2. Remove the air filter housing and air intake duct. 3. Remove the rear engine lifting eye. 4. Remove the vacuum hose. 5. Remove the...
Thermostat (Diesel Engines) — Checking After Removal
1. Check the thermostat valve closing at normal room temperature. It should be tightly closed. 2. Check the operation of the thermostat valve. To do this, tie the...
1. Check the thermostat valve closing at normal room temperature. It should be tightly closed. 2. Check the operation of the thermostat valve. To do this, tie the...
Service data and specification of the HR16DE engine
Cooling system capacity (approximate) Radiator Thermostat Heater thermostat (modifications with variator) Note: The table below provides reference values. Check valve
Cooling system capacity (approximate) Radiator Thermostat Heater thermostat (modifications with variator) Note: The table below provides reference values. Check valve
Service data and specification of the MR20DE engine
Cooling system capacity (approximate) Radiator Thermostat Heater thermostat (modifications with variator) Check valve
Cooling system capacity (approximate) Radiator Thermostat Heater thermostat (modifications with variator) Check valve
Service data and specification of the K9K engine
Cooling system capacity (approximate) Radiator Thermostat
Cooling system capacity (approximate) Radiator Thermostat
Service data and specification of the M9R engine
Cooling system capacity (approximate) Expansion tank cap Radiator Outlet pipe with thermostat assembly
Cooling system capacity (approximate) Expansion tank cap Radiator Outlet pipe with thermostat assembly
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar information for other Nissan models
➜ Power unit: Cooling system Nissan Murano 1 (2002-2007, petrol)
➜ Power unit: Cooling and heating Nissan Patrol 4 (1987-1997, petrol)
➜ Power unit: Cooling and heating Nissan Maxima 4 (1994-1999)
➜ Power unit: Cooling system (CR) Nissan Note 1 (2004-2013)
➜ Power unit: Cooling system Nissan Almera 1 (1995-2000)
➜ Power unit: Cooling system Nissan Bluebird T12 (1986-1991)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- Faults en route
- Daily checks
- User manual
- Maintenance
- Power unit
- Petrol engines 1.6L (HR16)
- Petrol engines 2.0L (MR20)
- Diesel engines 1.5L (K9K)
- Diesel engines 2.0L (M9R)
- Cooling system
- Engine lubrication system
- Engine power system
- Engine management system
- Intake and exhaust system
- Engine electrical equipment
- Transmission
- Clutch
- Car gearbox
- Transfer case and shafts
- Chassis
- Car suspension
- Brake system
- Steering
- Body
- Exterior (external elements)
- Interior (internal elements)
- Safety system
- Heating and air conditioning
- Electrical equipment
- Wiring harnesses
Cookies are used to improve the site's performance. 💻 Continue by agreeing to the terms.