Brake system of the car Nissan Terrano 1 (WD21)
Brake system specifications
Disc brakes Disc runout no more than 0.07 mm Uneven thickness of the disc no more than 0.02 mm Maximum disc thickness CL25VA (rear-wheel drive vehicles with 4-cylinder...
Disc brakes Disc runout no more than 0.07 mm Uneven thickness of the disc no more than 0.02 mm Maximum disc thickness CL25VA (rear-wheel drive vehicles with 4-cylinder...
General information about the braking system
The cars are equipped with dual-circuit hydraulic brakes, a vacuum booster and a rear brake pressure regulator (KlSLV - valve). The regulator is designed to unlock the...
The cars are equipped with dual-circuit hydraulic brakes, a vacuum booster and a rear brake pressure regulator (KlSLV - valve). The regulator is designed to unlock the...
Disc brake pads (front and rear) — replacement
Attention! The pads are changed only as a set for one axle. When cleaning the pads, remove dust and dirt by wiping with a rag soaked in alcohol; blowing is prohibited....
Attention! The pads are changed only as a set for one axle. When cleaning the pads, remove dust and dirt by wiping with a rag soaked in alcohol; blowing is prohibited....
Brake Caliper — Removal, Disassembly and Installation
Attention! The described operations apply to brakes equipped with both single-piston and block brakes (two-piston) cylinders. 1. Remove the pads. 2. Unscrew the hose...
Attention! The described operations apply to brakes equipped with both single-piston and block brakes (two-piston) cylinders. 1. Remove the pads. 2. Unscrew the hose...
Brake disc — inspection, removal and installation
Examination 1. Loosen the wheel nuts, lift the car and place it on stands. Remove the wheels. 2. Remove the caliper with the cylinder and set it aside. 3. Check the...
Examination 1. Loosen the wheel nuts, lift the car and place it on stands. Remove the wheels. 2. Remove the caliper with the cylinder and set it aside. 3. Check the...
Rear Drum Brakes — Pad Replacement
1. Raise the rear of the vehicle and support it on stands. Release the handbrake. 2. Remove the wheel. 3. If necessary, move the pads together using the adjuster ( Ch. 1...
1. Raise the rear of the vehicle and support it on stands. Release the handbrake. 2. Remove the wheel. 3. If necessary, move the pads together using the adjuster ( Ch. 1...
Rear Drum Brake Wheel Cylinder — Removal, Disassembly and Installation
1. Prepare the cylinder repair kit. 2. Remove the drums and shoes. 3. Place a tray underneath. 4. Clean the cylinder mounting bolts to the brake shield and the nipple...
1. Prepare the cylinder repair kit. 2. Remove the drums and shoes. 3. Place a tray underneath. 4. Clean the cylinder mounting bolts to the brake shield and the nipple...
Rear brake discs — inspection, removal and installation
1. Tighten 2 wheel nuts to hold the disc against the axle flange and check the disc condition ( see section 5 ). 2. Remove the cylinder, unscrew the bolts securing the...
1. Tighten 2 wheel nuts to hold the disc against the axle flange and check the disc condition ( see section 5 ). 2. Remove the cylinder, unscrew the bolts securing the...
Handbrake pads (on rear disc brakes) — removal, installation and adjustment
Removal 1. Remove the rear brake disc. 2. Remove the brake shoe pressure springs by pressing on the cap and turning it 90° (photo). 9.2 Rear Disc Brake Handbrake Parts...
Removal 1. Remove the rear brake disc. 2. Remove the brake shoe pressure springs by pressing on the cap and turning it 90° (photo). 9.2 Rear Disc Brake Handbrake Parts...
Brake Master Cylinder — Removal, Disassembly and Installation
1. Disconnect the battery from ground. 2. Place a tray or a rag underneath. 3. Loosen the tube fittings on the master cylinder (photo). 10.3 Nuts of the nipples on the...
1. Disconnect the battery from ground. 2. Place a tray or a rag underneath. 3. Loosen the tube fittings on the master cylinder (photo). 10.3 Nuts of the nipples on the...
Brake pressure regulator — removal and installation
Attention! The regulator is non-disassemblable and must be replaced in case of failure. 1. Unscrew the fittings and plug the holes in the pressure regulator. 2. Unscrew...
Attention! The regulator is non-disassemblable and must be replaced in case of failure. 1. Unscrew the fittings and plug the holes in the pressure regulator. 2. Unscrew...
Hydraulic line — check and replacement
1. Check the condition of the hoses and tubes every 6 months; if cracks, leaks, abrasions or other damage are detected, replace the hose or tube. 2. Select new tubes...
1. Check the condition of the hoses and tubes every 6 months; if cracks, leaks, abrasions or other damage are detected, replace the hose or tube. 2. Select new tubes...
Bleeding the brakes
Attention! Before bleeding the brakes on cars equipped with ABS, disconnect the battery from the ground. It is recommended to bleed the brakes with two people. 1. The...
Attention! Before bleeding the brakes on cars equipped with ABS, disconnect the battery from the ground. It is recommended to bleed the brakes with two people. 1. The...
Brake booster — general information and testing
1. The vacuum booster is designed to increase the force on the pistons of the master cylinder due to the vacuum created in the engine intake manifold. 2. During...
1. The vacuum booster is designed to increase the force on the pistons of the master cylinder due to the vacuum created in the engine intake manifold. 2. During...
Vacuum brake booster — removal and installation
1. Remove the master cylinder. 2. Disconnect the hose. 3. Disconnect the booster rod from the brake pedal by removing the axle (photo). 15.3 Vacuum booster 1. Pedal...
1. Remove the master cylinder. 2. Disconnect the hose. 3. Disconnect the booster rod from the brake pedal by removing the axle (photo). 15.3 Vacuum booster 1. Pedal...
Handbrake — adjustment
1. Adjustment of the handbrake is necessary due to the cable stretching during operation, or when disassembling the rear brake. 2. Apply the handbrake with maximum...
1. Adjustment of the handbrake is necessary due to the cable stretching during operation, or when disassembling the rear brake. 2. Apply the handbrake with maximum...
Handbrake lever — removal and installation
1. Disconnect the wire connector leading to the lever. 2. Disconnect the cable end by removing the axle. 3. Loosen the bolts and screw securing the lever bracket to the...
1. Disconnect the wire connector leading to the lever. 2. Disconnect the cable end by removing the axle. 3. Loosen the bolts and screw securing the lever bracket to the...
Handbrake cables — removal and installation
Front cable 1. Release the brake lever. 2. Disconnect the cable from the lever (photo). 18.2 Parts of the handbrake drive of the Terrano I/Pathfinder 1. Rear cable 2....
Front cable 1. Release the brake lever. 2. Disconnect the cable from the lever (photo). 18.2 Parts of the handbrake drive of the Terrano I/Pathfinder 1. Rear cable 2....
Brake light switch — removal and installation
1. The switch is mounted behind the brake pedal. 2. Disconnect the wires from the switch. 3. Loosen the lock nut. 4. Unscrew the switch. 5. Install the switch in the...
1. The switch is mounted behind the brake pedal. 2. Disconnect the wires from the switch. 3. Loosen the lock nut. 4. Unscrew the switch. 5. Install the switch in the...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar information for other Nissan models
➜ Chassis: Brake system Nissan Micra 3 (2002-2010, petrol)
➜ Chassis: Brake system Nissan Almera 1 (1995-2000)
➜ Chassis: Brake system Nissan Patrol 4 (1987-1997, petrol)
➜ Chassis: Brake system Nissan Primera 1 (1990-1996, petrol)
➜ Chassis: Brake system Nissan Maxima 4 (1994-1999)
➜ Chassis: Brake system Nissan Sunny 7 (1990-1998)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Maintenance
- Power unit
- Engines 4-cylinder
- Engines 6-cylinder
- Engine overhaul
- Cooling and ventilation
- Fuel and exhaust systems
- Engine electrical equipment
- Decreased toxicity
- Transmission
- Mechanical gearbox
- Automatic gearbox
- Clutch and drive shafts
- All-wheel drive system
- Chassis
- Brake system
- Car suspension
- Steering
- Body and electrical equipment
- Body elements
- Doors, locks and windows
- Equipment and devices
Cookies are used to improve the site's performance. 💻 Continue by agreeing to the terms.