Car front suspension Nissan Serena 2 (C24)
Front axle — check
Check the front wheel bearings for excessive play. Raise the vehicle and check the following. Move the wheel hub axially by hand. Check the play of the front wheel...
Check the front wheel bearings for excessive play. Raise the vehicle and check the following. Move the wheel hub axially by hand. Check the play of the front wheel...
Front suspension — check
Check suspension components for loose fasteners, excessive play, and damage. Raise the vehicle and check the following. Check that all components are securely fastened...
Check suspension components for loose fasteners, excessive play, and damage. Raise the vehicle and check the following. Check that all components are securely fastened...
Adjusting the front wheel alignment angles
Measure the front wheel alignment angles with the vehicle in an unladen condition, which means full of fuel, coolant and engine oil. However, the spare tire, jack and...
Measure the front wheel alignment angles with the vehicle in an unladen condition, which means full of fuel, coolant and engine oil. However, the spare tire, jack and...
Front axle — removal and installation
Removal 1. Remove the wheels, remove the brake hose retaining plates from the rack. 2. Remove the brake caliper from the steering knuckle. Hang the caliper so that it...
Removal 1. Remove the wheels, remove the brake hose retaining plates from the rack. 2. Remove the brake caliper from the steering knuckle. Hang the caliper so that it...
Front axle — disassembly and assembly
Disassembly 1. Secure the steering knuckle in a vice at the strut mounting location. Press the wheel hub out of the steering knuckle using an impact puller (special...
Disassembly 1. Secure the steering knuckle in a vice at the strut mounting location. Press the wheel hub out of the steering knuckle using an impact puller (special...
Suspension beam — removal and installation
Removal 1. Remove the steering knuckles from the vehicle, see above. 2. Remove the front exhaust pipe. 3. 4WD models: Remove the driveshaft from the vehicle. 4. Remove...
Removal 1. Remove the steering knuckles from the vehicle, see above. 2. Remove the front exhaust pipe. 3. 4WD models: Remove the driveshaft from the vehicle. 4. Remove...
Racks — removal and installation
Removal Active suspension models: Remove the drives and insulator covers from the bushings. Caution: Do not hit or drop the drive. 1. Remove the wheel. Remove the brake...
Removal Active suspension models: Remove the drives and insulator covers from the bushings. Caution: Do not hit or drop the drive. 1. Remove the wheel. Remove the brake...
Racks — disassembly and assembly
1. Install the attachment (special tool) onto the assembled stand and secure it in a vice. Caution: To avoid damage to the stand, wrap the stand with a cloth before...
1. Install the attachment (special tool) onto the assembled stand and secure it in a vice. Caution: To avoid damage to the stand, wrap the stand with a cloth before...
Wishbones — Removal and Installation
Removal 1. Remove the steering knuckle from the wishbone, see above. 2. Remove the anti-roll bar connecting rod bracket from the transverse arm. 3. Loosen the wishbone...
Removal 1. Remove the steering knuckle from the wishbone, see above. 2. Remove the anti-roll bar connecting rod bracket from the transverse arm. 3. Loosen the wishbone...
Transverse stability stabilizer
Removal 2WD models 1. Unscrew the upper mounting nuts of the anti-roll bar connecting rods. 2. Unscrew the stabilizer clamp mounting bolts. 3. Remove the steering gear,...
Removal 2WD models 1. Unscrew the upper mounting nuts of the anti-roll bar connecting rods. 2. Unscrew the stabilizer clamp mounting bolts. 3. Remove the steering gear,...
Wheels and tires — general information
Attention: Install only genuine NISSAN aluminum wheels on your vehicle. To ensure a press fit on NISSAN aluminum wheels, steel cone nuts are used. Install the wheels...
Attention: Install only genuine NISSAN aluminum wheels on your vehicle. To ensure a press fit on NISSAN aluminum wheels, steel cone nuts are used. Install the wheels...
Road wheels
Checking the appearance Check the wheels for deformation, cuts, damage, corrosion, etc. Checking the wheel runout Raise the car. Remove the tire from the rim. Install...
Checking the appearance Check the wheels for deformation, cuts, damage, corrosion, etc. Checking the wheel runout Raise the car. Remove the tire from the rim. Install...
ADS system fault diagnostics
Standard voltages of input/output signals of the ADS control unit Checking components Automatic transmission mode switch Disconnect the wiring connector from the switch,...
Standard voltages of input/output signals of the ADS control unit Checking components Automatic transmission mode switch Disconnect the wiring connector from the switch,...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar information for other Nissan models
➜ Chassis: Front suspension Nissan Almera 1 (1995-2000)
➜ Chassis: Front suspension Nissan X-Trail 2 (2007-2013, petrol)
➜ Chassis: Front suspension Nissan Murano 1 (2002-2007, petrol)
➜ Chassis: Front suspension Nissan Primera 1 (1990-1996, petrol)
➜ Chassis: Front axle and suspension Nissan Patrol 4 (1987-1997, petrol)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- Control devices
- User manual
- Power unit
- Petrol engine SR20DE
- Diesel engine YD25DDTi
- Cooling and lubrication system
- Engine management SR20DE
- Engine management YD25DDTi
- Power and exhaust system
- Transmission
- Automatic gearbox
- Drive and cardan shafts
- Transfer case
- Chassis
- Front suspension
- Rear suspension
- Brake system
- Steering
- Body
- Safety system
- Interior (internal elements)
- Exterior (external elements)
- Doors, locks and windows
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Lighting system
- Windshield wipers and washers
- Electrical circuits
Cookies are used to improve the site's performance. 💻 Continue by agreeing to the terms.