Drive and cardan shafts of the car Nissan Serena 2 (C24)
Front Drive Shafts — Removal and Installation
Removal 1. Remove the cotter pin. Unscrew the lock nut using a hub nut wrench (special tool). 2. Remove the ABS sensor from the steering knuckle. 3. Remove the steering...
Removal 1. Remove the cotter pin. Unscrew the lock nut using a hub nut wrench (special tool). 2. Remove the ABS sensor from the steering knuckle. 3. Remove the steering...
Front Drive Shafts — Disassembly
Checking before disassembly Move the hinge up/down, left/right and axially. Make sure it moves freely and there is no significant play. Check the covers for cracks,...
Checking before disassembly Move the hinge up/down, left/right and axially. Make sure it moves freely and there is no significant play. Check the covers for cracks,...
Front Drive Shafts — Check
Shaft If runout, cracks or damage are found, replace the shaft. Covers and clamps If cracks are found, replace the cover. If removed, the cover clamps should be replaced...
Shaft If runout, cracks or damage are found, replace the shaft. Covers and clamps If cracks are found, replace the cover. If removed, the cover clamps should be replaced...
Front Drive Shafts — Assembly
Thrust bearing (Z100D90+B, B90SFJ90+B) 1. Press the support bearing into the housing using a drift (special tool). 2. Secure the support bearing with the retaining ring....
Thrust bearing (Z100D90+B, B90SFJ90+B) 1. Press the support bearing into the housing using a drift (special tool). 2. Secure the support bearing with the retaining ring....
Rear Drive Shafts — Removal and Installation
Removal 1. Remove the rear axle. See Ch. Rear axle and suspension . Caution: If removing the rear axle only to remove the drive shaft assemblies, loosen the fasteners on...
Removal 1. Remove the rear axle. See Ch. Rear axle and suspension . Caution: If removing the rear axle only to remove the drive shaft assemblies, loosen the fasteners on...
Rear Drive Shafts — Disassembly
Checking before disassembly Move the hinge up/down, left/right and axially. Make sure it moves freely and there is no significant play. Check the covers for cracks,...
Checking before disassembly Move the hinge up/down, left/right and axially. Make sure it moves freely and there is no significant play. Check the covers for cracks,...
Rear Drive Shafts — Checking
Shaft If runout, cracks or damage are found, replace the shaft. Covers and clamps If cracks are found, replace the cover. If removed, the cover clamps should be replaced...
Shaft If runout, cracks or damage are found, replace the shaft. Covers and clamps If cracks are found, replace the cover. If removed, the cover clamps should be replaced...
Rear Drive Shafts — Assembly
From the wheel side 1. Press the sensor signal ring into the hinge assembly using a punch (special tool). Note: Replace the old sensor signal ring with a new one. Note:...
From the wheel side 1. Press the sensor signal ring into the hinge assembly using a punch (special tool). Note: Replace the old sensor signal ring with a new one. Note:...
Cardan shaft assembly
Removal 1. Apply alignment marks to the flanges of the propeller shaft forks, connecting flanges of the main gear and transfer case. Note: Apply marks with paint. 2....
Removal 1. Apply alignment marks to the flanges of the propeller shaft forks, connecting flanges of the main gear and transfer case. Note: Apply marks with paint. 2....
Main gear assembly — testing on the vehicle
Oil in the differential Replacement interval: For individual use of the vehicle: after major repairs. For commercial use of the vehicle: every 100,000 km or once every 2...
Oil in the differential Replacement interval: For individual use of the vehicle: after major repairs. For commercial use of the vehicle: every 100,000 km or once every 2...
Main gear assembly — front oil seal
Removal 1. Remove the driveshaft. 2. Align the final drive flange and the threaded end of the ATC coupling and make marks. Caution: Apply alignment marks with paint. Do...
Removal 1. Remove the driveshaft. 2. Align the final drive flange and the threaded end of the ATC coupling and make marks. Caution: Apply alignment marks with paint. Do...
Main gear assembly — axle shaft seals
Removal 1. Remove the drive shaft. 2. Remove the oil seal using a screwdriver. Installation 1. Apply special Nissan MP #2 grease to the edges of the seal. Press the seal...
Removal 1. Remove the drive shaft. 2. Remove the oil seal using a screwdriver. Installation 1. Apply special Nissan MP #2 grease to the edges of the seal. Press the seal...
Main gear assembly — clutch with automatic variable torque (ATC)
Removal 1. Remove the driveshaft. 2. Align the final drive flange and the threaded end of the ATC coupling and make marks. Caution: Apply alignment marks with paint. Do...
Removal 1. Remove the driveshaft. 2. Align the final drive flange and the threaded end of the ATC coupling and make marks. Caution: Apply alignment marks with paint. Do...
Main gear assembly — removal and installation
Preparatory work Remove the propeller shaft, see above. Remove the rear drive shafts, see chapter Drive shafts . Disconnect the breather hose. Remove the front and rear...
Preparatory work Remove the propeller shaft, see above. Remove the rear drive shafts, see chapter Drive shafts . Disconnect the breather hose. Remove the front and rear...
Main gear assembly — check
Gear engagement 1. Drain the oil. 2. Remove the back cover. 3. Install special tools. 4. Apply red lead to the drive gear flange. Note: Apply red lead evenly in 3-4...
Gear engagement 1. Drain the oil. 2. Remove the back cover. 3. Install special tools. 4. Apply red lead to the drive gear flange. Note: Apply red lead evenly in 3-4...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar information for other Nissan models
➜ Transmission: Drive shafts Nissan Bluebird T12 (1986-1991)
➜ Transmission: Drive shafts Nissan Murano 1 (2002-2007, petrol)
➜ Transmission: Drive shafts Nissan Sunny 7 (1990-1998)
➜ Transmission: Transfer case and shafts Nissan Qashqai 1 (2006-2013)
➜ Transmission: Drive shafts and hubs Nissan Micra 3 (2002-2010, petrol)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- Control devices
- User manual
- Power unit
- Petrol engine SR20DE
- Diesel engine YD25DDTi
- Cooling and lubrication system
- Engine management SR20DE
- Engine management YD25DDTi
- Power and exhaust system
- Transmission
- Automatic gearbox
- Drive and cardan shafts
- Transfer case
- Chassis
- Front suspension
- Rear suspension
- Brake system
- Steering
- Body
- Safety system
- Interior (internal elements)
- Exterior (external elements)
- Doors, locks and windows
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Lighting system
- Windshield wipers and washers
- Electrical circuits
Cookies are used to improve the site's performance. 💻 Continue by agreeing to the terms.