Doors, locks and windows of the car Nissan Serena 2 (C24)
Side front windows — removal and installation Preparatory work Remove the side section of the dashboard. Remove the front pillar trim. Remove the body seal. Remove the front strut trim. Removing 1. To prevent damage...
Rear door glass — removal and installation Preparatory work Remove the curtain (if available). Remove the upper brake light. Remove the overlay. Remove the rear wiper arm (if available). Disconnect the rear...
Adjusting the fit of the front doors Front and rear level adjustment Adjustment area: fastening of the hinges on the body side. Preparatory work Remove the wing protector. Adjustment Loosen the hinge...
Front door assembly Note: Support the door with a jack when removing and installing the door assembly. Place a cloth over the head of the jack to prevent damage to the door or bodywork....
Front door locks — check and adjustment Preparatory work Remove the front door trim. Remove the protective screen. Note: If the screen is to be reused, do not cut off its butyl tape. Toggle Adjustment Note:...
Front door locks — removal and installation Removing Preparatory work Remove the front door trim. Remove the protective screen. Note: If the screen is to be reused, do not cut off its butyl tape. Close the door...
Front door locks — disassembly and assembly Disassembly Note: Disconnect the actuator, remove the door lock assembly from the vehicle. 1. Unscrew the fixing screws of the door lock drive. 2. Pull the drive down...
Front door glass — general information Fit check Make sure the glass fits snugly into the groove of the guide. Raise and lower the glass and check if there are any problems while the glass is moving....
Front door glass — removal and installation 1. Using the main power window switch, lower the window so that the mounting bolts of the carrier are visible. 2. Loosen the mounting bolts of the support element. 3....
Front door glass — check and adjustment Examination Check the power window assembly as indicated below. If abnormalities are found, replace or apply lubricant. Check: is the cable worn out; whether the window...
Sliding door fit adjustment Gap adjustment Loosen the rear roller fixing bolts, loosen the roller bracket nuts and adjust the position of the door by moving it forward or backward. Level control...
Sliding door assembly Removal and installation Attention: Before removing and installing, wrap the body and door parts with a cloth to prevent damage to them. Preparatory work Remove the...
Sliding door lock — adjustment Preparatory work Remove the sliding door trim. Remove the protective screen. Note: If the screen is to be reused, do not cut off its butyl tape. Remote control cable...
Sliding door lock — removal and installation Preparatory work Remove the sliding door trim. Remove the protective screen. Note: If the screen is to be reused, do not cut off its butyl tape. Remove the power window...
Sliding door lock — check Remote control unit (DU) Lubricate all grooves with body grease if necessary. Lock and automatic closing unit If necessary, lubricate the lock latch area and lever...
Sliding door glass — adjustment Preparatory work Remove the sliding door trim. Remove the protective screen. Note: If the screen is to be reused, do not cut off its butyl tape. Fit adjustment Lower the...
Power window and glass Preparatory work Remove the sliding door trim. Remove the protective screen. Note: If the screen is to be reused, do not cut off its butyl tape. Remove the door outer...
Remote control door locks — general information Description Using the remote control, you can lock and unlock all doors, incl. back. If, after pressing the unlock button, the doors are not opened for approx. 30...
Checking the door lock remote control system Troubleshooting Component Check Checking the battery Standard voltage: approx. 2.5-3.0V Note: The current strength when connecting a load of 300W to the battery is...
Power windows — general information Description After turning the ignition key to the OFF position, the timer runs for 15 minutes, during which time the power windows can be operated with the switch on the...
Sliding door automatic closing system Location of components Wiring diagram Standard input/output voltages of the automatic closing control unit Troubleshooting Before starting the diagnostics, open and...
Side window Before removing the window, remove the rear pillar and rear door pillar trim.
Rear door — general information Fit adjustment Gap adjustment top/bottom and right/left Adjustment areas: Mounting bolts hinges on the side of the rear door Hinge fixing screws Adjustment procedure:...
Back door assy Preparatory work Remove the rear door wiring harness rubber grommet. Disconnect the rear door wiring connector. Removal and installation Secure the rear door lock...
Rear door lock Preparatory work Remove the rear door trim. Disconnect the rod holders. Disconnect the drive wiring connector. Remove the protective screen. Note: If the screen is to be...
Sunroofs — adjustment Fit adjustment Gap adjustment front/rear and right/left (front and back covers) Preparatory work Remove the side trim. 1. Loosen the fixing nuts of the glass cover. 2....
Front hatch Sunscreen unit - removal and installation Preparatory work Remove the front headlining. Remove the screen assembly, remove the stopper from the assembly, then remove the...
Rear hatch block — removal and installation Attention: Before removing the sunroof assembly, cover the seats and trim with rags to prevent damage. After installing the sunroof assembly and glass cover, test for...
Rear hatch block — disassembly and assembly Disassembly The sunroof block is disassembled after it is removed from the vehicle. However, the glass cover, deflector and motor can be removed and installed on the...
Hatch electrical equipment Location of components Wiring diagram Standard Input/Output Voltages of Front Seat Switch Standard input/output switch box voltages Troubleshooting