Table of contents: How to switch between self-diagnosis…↓ How to clear self-diagnosis results ↓ Table of indicator lamp blinking…↓ Lamp blinking patterns ↓
Reading of results is performed in one of two modes: user and diagnostic.
After troubleshooting, turn the ignition key to the "ON" position. The diagnostic mode switches to the user mode. In this case, the self-diagnostic result is erased.
How to switch between self-diagnosis modes.
Attention:
- In the user mode, when the "AIR BAG" indicator lamp does not flash, switching to the diagnostic mode using the ignition key is not possible.
- In diagnostic mode, when no faults are detected, you can switch to user mode by turning the ignition key from the "OFF" position to the "ON" position.
How to clear self-diagnosis results
After troubleshooting, turn the ignition key to the "OFF" position for at least one second, then back to the "ON" position. The diagnostic mode switches to the user mode. In this case, the self-diagnostic result is erased.
Table of indicator lamp blinking codes
After troubleshooting the faults or intermittent faults detected earlier, the diagnostic results (previously entered into memory) may not be erased from memory.
Lamp blinking patterns
Troubleshooting procedure:
- 1. Erase the memory contents. (The diagnostic results are erased after turning the ignition key from the "OFF" position to the "ON" position.)
Driver airbag module
Troubleshooting procedure:
- 1. Perform a visual inspection of the electrical wiring connectors.
- 2. If visible damage is found, replace the electrical wiring.
- 3. Replace the coil wire.
- 4. Replace the driver's airbag module (It should be unfolded before disposal)
- 5. Replace the diagnostic sensor unit.
- 6. Replace adjacent electrical wiring.
Diagnostic sensor block
Troubleshooting procedure:
- 1. Perform a visual inspection of the electrical wiring connectors
- 2. If visible damage is found, replace the electrical wiring.
- 3. Replace the diagnostic sensor unit
- 4. Replace adjacent electrical wiring.
Front passenger airbag module
Troubleshooting procedure:
- 1. Perform a visual inspection of the electrical wiring connectors.
- 2. If visible damage is found, replace the electrical wiring.
- 3. Replace the front passenger airbag module. (It should be unfolded before disposal).
- 4. Replace the diagnostic sensor unit.
- 5. Replace adjacent electrical wiring.
Original text on the website [nissanbook.ru]
Shock sensor
Troubleshooting procedure:
- 1. Perform a visual inspection of the electrical wiring connectors.
- 2. If visible damage is found, replace the electrical wiring.
- 3. Replace the shock sensor.
- 4. Replace the diagnostic sensor unit.
- 5. Replace adjacent electrical wiring.
Front right seat belt pretensioner
Troubleshooting procedure:
- 1. Perform a visual inspection of the electrical wiring connectors.
- 2. If visible damage is found, replace the electrical wiring.
- 3. Replace the front right seat belt pretensioner. (Before disposal it should be rendered inoperative).
- 4. Replace the diagnostic sensor unit.
- 5. Replace adjacent electrical wiring.
Front left seat belt pretensioner
Troubleshooting procedure:
- 1. Perform a visual inspection of the electrical wiring connectors.
- 2. If visible damage is found, replace the electrical wiring.
- 3. Replace the front left seat belt pretensioner (Before disposal it should be rendered inoperative).
- 4. Replace the diagnostic sensor unit.
- 5. Replace adjacent electrical wiring.
Right airbag side impact sensor
Troubleshooting procedure:
- 1. Perform a visual inspection of the electrical wiring connectors.
- 2. If visible damage is found, replace the electrical wiring.
- 3. Replace the right airbag side impact sensor.
- 4. Replace the diagnostic sensor unit.
- 5. Replace adjacent electrical wiring.
Left Airbag Side Impact Sensor
Troubleshooting procedure:
- 1. Perform a visual inspection of the electrical wiring connectors.
- 2. If visible damage is found, replace the electrical wiring.
- 3. Replace the left airbag side impact sensor.
- 4. Replace the diagnostic sensor unit.
- 5. Replace adjacent electrical wiring.
Front Right Side Airbag Module
Troubleshooting procedure:
- 1. Perform a visual inspection of the electrical wiring connectors.
- 2. If visible damage is found, replace the electrical wiring.
- 3. Replace the front right side airbag module (It should be unfolded before disposal).
- 4. Replace the diagnostic sensor unit.
- 5. Replace adjacent electrical wiring.
Front Left Side Airbag Module
Troubleshooting procedure:
- 1. Perform a visual inspection of the electrical wiring connectors.
- 2. If visible damage is found, replace the electrical wiring.
- 3. Replace the front left side airbag module (It should be unfolded before disposal).
- 4. Replace the diagnostic sensor unit.
- 5. Replace adjacent electrical wiring.
Right side curtain airbag module
Troubleshooting procedure:
- 1. Perform a visual inspection of the electrical wiring connectors.
- 2. If visible damage is found, replace the electrical wiring.
- 3. Replace the right side curtain airbag module (It should be unfolded before disposal).
- 4. Replace the diagnostic sensor unit.
- 5. Replace adjacent electrical wiring.
Left side curtain airbag module
Troubleshooting procedure:
- 1. Perform a visual inspection of the electrical wiring connectors.
- 2. If visible damage is found, replace the electrical wiring.
- 3. Replace the left side curtain airbag module (It should be unfolded before disposal).
- 4. Replace the diagnostic sensor unit
- 5. Replace adjacent electrical wiring